These engine and transmission compression testers are built with a compact design that is easy to use and store in a toolbox. The tester kits include everything you need to perform a cylinder compression test in your car, truck, or tractor, as well as educational recommendations to help keep you safe while working on your vehicles. In the event that a valve core fails, replace only with a special valve core from the dealer.Easily and accurately check the compression on your engine, whether it be diesel or petrol. Usually by running an engine with the compression tester attached and holding down the side release valve, the foreign matter will be blown out. If, at some point after usage, the tool does not hold pressure the probable cause is foreign matter in either the release valve or the valve core in the adapter. This compression tester has been completely tested at the factory for accuracy and leakage before shipment. Push the side release valve to release pressure.
The reading is shown and held on the gauge. Run, or turn over the engine to the manufacturer's specs until the maximum pressure is reached, usually with 8-12 strokes of the engine. Make sure the locking sleeve on the quick coupler of the tester slides completely into place. With the correct adapter in place on the engine, attach the compression tester to the adapter. The top of the adapter has a male quick disconnect to accommodate the compression tester. The adapters are designed to be threaded into or clamped into, the glow plug or injector hole in the same way the glow plug or injector is attached to the engine. IMPORTANT: Always check the engine manufacturer's recommendations for compression testing before test. Turn the engine over for a few revolutions to blow out any carbon or foreign matter from the port area before connecting the adapter. Remove the glow plug or injector from the cylinder to be tested and shut off or bypass the fuel to that cylinder. The adapters are designed to replace either the glow plug or the injector on the engine. To do a compression test select the proper adapter for the engine to be tested. Please see list below for complete list of the additional adapters available:Ģ800X01 M10 x 1.00 - Diesel Compression Adapter - ShortĢ800X02 M24 x 2.00 - Diesel Compression Adapter - LongĢ800X03 M10 x 1.00 - Diesel Compression Adapter - LongĢ800X04 M10 x 1.25 - Diesel Compression Adapter - LongĢ800X05 M10 x 1.25 - Diesel Compression Adapter - ShortĢ800X06 M22 x 1.50 - Diesel Compression AdapterĢ800X07 M10 x 1.25 - Diesel Compression Adapter - MediumĢ800X08 M10 x 1.00 - Diesel Compression Adapter - Extra LongĢ800X09 M24 x 2.00 - Diesel Compression Adapter - ShortĢ800X10 M22 x 1.50 - Diesel Compression Adapter - LongĢ800X11 M12 x 1.25 - Diesel Compression AdapterĢ800X12 M10 x 1.00 - Diesel Compression Adapter - Extra LongĢ800X13 M24 x 2.00 - Diesel Compression Adapter - MediumĢ800X14 M18 x 1.50 - Diesel Compression AdapterĢ800X16đ" & 7/8" - Diesel Compression AdapterĢ800X18 M14 x 1.25 - Diesel Compression AdapterĢ800X19 M24 x 1.50 - Diesel Compression AdapterĢ800X20 M17 - Diesel Compression Adapter - 1x GapĢ800X21 M17 - Diesel Compression Adapter - 2x GapĢ800X22ē/8" - Diesel Compression AdapterĢ800X23ė/8" x 14 - Diesel Compression AdapterĢ800X24 M10 x 1.00 - Diesel Compression Adapter - Flex HoseĢ800X25Ĕ" Extension - Diesel Compression AdapterĢ800X26 M8 x 1.00 - Diesel Compression AdapterĢ800X27 ISB/ISC - Diesel Compression Adapter - InjectorĢ800X28 M14 x 1.25 - Diesel Compression Adapter - Flex HoseĢ800X29ğord 6.7L - Diesel Compression Adapter
#Diesel compression tester kit full#
Includes Adapter No 2800x02 for VW, Volvo, Audi, Dodge, Mercedes and Cummins 5.9L (24mm x 20) injector applicationsĪlso includes Adaptor No 2800x03 for GM 6.2L V8 10mm x 10 Glow Plug applicationsĬlick 'Application Chart' for full applications!ĪTTENTION - If gauge assembly is removed, re-apply thread seal when replacing gauge. Includes Adapter No 2800x01 for GM 4.3L 6-cyl, 4.3L and 5.7L 8-cyl, Ford/Navistar 6.9L and 7.3L, Int Harvester 6.9L 10mm x 10 Glow Plug applications Kit includes 13-Inch / 33cm flexible hose with swivel end quick coupler Note: Features a 2-1/2-Inch / 63mm-diameter gauge with dual-calibration (0 - 1,000 PIS / 0 - 70kg/cm2) and side-release valve for multiple readings without removing adapter
0 kommentar(er)
